Zenith Z62DC1D Manual do Proprietário

3-2 DURING OPERATION (PAYING ATTENTION TO CUSTOMERS)To avoid injury and trouble, be sure to pay attention to the behavior of visitors and players.To

4. PART DESCRIPTIONS62” DLP PROJECTOR52” DLP PROJECTOR29” CRT MONITOR 31KCONTROL PANELSIDE DOOR (R)SIDE DOOR (L)> Other sideCONTROL UNIT (GUN)BILL

Confi rm that the accessories listed in the table below are present when setting up the product. Accessories marked “Spare” in the note column are cons

Be very careful when handling the projector screen. The screen is easily damaged but cannot be repaired. If damaged the entire screen must bereplaced.

INSTALLING MONITOR, 52"/62"DX1This game is provided with either a 52 or 62 monitor dependant upon the model purchased. At least 2 people a

After the game is joined and stabilized, using two people, place the monitor on top of the platform shown (Figure 5) with the screen side of the monit

11Install the Plexiglas shield4 and its retaining strips5 on the monitor side protectors6(Figure 8A). Locate the rectangular tubing7 (Figure 9) in the

Connect the Mask assembly (Figure 13) to the monitor using the attached hardware. Be careful to connect the plug (Figure 14) on the left side of the

Using at least two people and step ladders, guide the marquee assembly onto the weldment marquee support3, by inserting the two rectangular tubes7 thr

SECURING IN PLACE2Make sure that all the adjusters are resting on the fl oor. The cabinet may move and cause an accident if the adjusters are not laid

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:To maintain safety:To ensure the safe operation of this product, be sure to read the followin

ASSEMBLY CHECK4Use Test Mode to check that the product has been assembled correctly and that the game board, other connected boards and all output dev

Interference Prevention WiringIn order to prevent electric shock and short circuit hazards, be sure to turn power off before performing work. Be caref

7. PRECAUTIONS WHEN MOVING THE MACHINEWhen moving the machine, be sure to pull out the plug from the power supply. Moving the machine with the plug s

8. GAME DESCRIPTIONThe following explanations apply to the product when functioning properly. If the product operates differently from the following

- Players can defend themselves against oil drums, rocks and axes thrown by enemies by shooting them.- Shooting the background will sometimes cause

9. EXPLANATION OF TEST AND DATA DISPLAYPeriodically use the TEST Button and SERVICE Buttons inside the cabinet to perform operation tests and check d

9-1 SWITCH UNIT AND COIN METERNever touch places other than those specifi ed. Touching places not specifi ed can cause electric shock and short circui

a. SYSTEM INFORMATIONSYSTEM INFORMATIONMOTHER BOARDSERIAL NO. AAGE-XXXXXXXXXXXXXKERNEL VERSION 2.4.20_m131aBOOT VERSION 1.00 (BUILD 0009)REGION XXMEMO

c-1. JVS INPUT TESTUse the JVS INPUT TEST to test the JVS input.The hexadecimal input information from the JVS I/O board will be displayed in real tim

f. COIN ASSIGNMENTSUse COIN ASSIGNMENTS to alter the credit settings.The game will award players the number of credits determined here. Settings will

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:TABLE OF CONTENTSINTRODUCTION1. HANDLING PRECAUTIONS...

COIN ASSIGNMENTSDETAIL SETTINGCOIN CHUTE #1 MULTIPLIER1 COIN COUNT AS 1 COIN(S)COIN CHUTE #2 MULTIPLIER1 COIN COUNT AS 1 COIN(S)BONUS ADDER NO BONUS

h. NETWORK SETTINGUse NETWORK SETTING to determine network settings or to test the network.This product does not use the network function. You must us

a. INPUT TESTSelect INPUT TEST to display the following screen and check the status of input devices. This test should be used periodically to check t

d. GUN CALIBRATION SETTINGSelect GUN CALIBRATION SETTING to display the following screen.Perform the sight settings for the guns to be used in the gam

Aim and fi re at the mark to the lower right. The mark to the lower right will disappear, and thesame mark will be displayed in the center.(Press the T

e. GUN SPEED SETTINGAdjust the volume settings for the Control Unit’s (Gun’s) speed sensors.Select GUN SPEED SETTING on the Game Test Mode screen and

Press the TEST Button and the message “NOW CALCULATING” will be displayed on the screen, and it will then proceed automatically to the next screen.The

f. BOOKKEEPINGSelect BOOKKEEPING on the Game Test Mode screen to display the three screens of operating status data.The display items for the screen (

10. CONTROL UNIT (GUN)In order to prevent any electric shocks or short circuits, be sure to turn the power off before performing any work that involve

3) Place cover R face down on the work surface and slowly lift cover L directly upward.4) Lift the trigger microswitch up from where

INTRODUCTIONThis manual is intended to provide detailed descriptions together with all the necessaryinformation covering the general operation of elec

Replacing the Sensor Unit1) Follow steps 1) to 3) above of the microswitch replacement procedure. You will now have removed cover L.2) Undo the

11. DLP (Digital Light Processor) PROJECTOR (52” = LG, 62” = Mitsubishi, LG, TOSHIBA and ZENITH)If the adjustment method in this manual does not re

12-1 BILLBOARD FLUORESCENT LIGHT (52”/62”DX)1) Turn the power off.2) Use the enclosed Tamper screws wrench (L-wrench) to remove the 5 washers

13. PERIODIC INSPECTIONThe items listed below require periodic check and maintenance to retain the performance of this machine and to ensure safe bus

14. TROUBLESHOOTINGIn order to prevent electric shock and short circuit, be sure to turn power off before performing work.Be careful not to damage th

PROBLEMS CAUSE COUNTERMEASURESControl Unit (Gun) sighting is not satisfactory.The Control Unit (Gun) does not appear to be operating correctly.The flu

Replacing the LED BoardRemoving or attaching of the mask must be carried out by at least two people, one on the left and one on the right. A single pe

U NUT (2)LED BOARD838-13145R02PHOTO 14.1 e5) If the problematic LED board is in the corner of the mask remove the 5 screws and remove the joint brack

14-2 ERROR CODESIf an error code is displayed get on-site maintenance personnel or other qualifi ed professional to look at it. An unqualifi ed person a

Error 14DISPLAY Network fi rmware version does not fulfi ll the game spec. Required version XX.XX.CAUSE The fi rmware version installed on either the

Definition of "Site Maintenance Personnel" or "Other Qualified Professionals"Procedures not described in this manual or marked as

Error 37DISPLAY Verifying Game Program Failed.CAUSE The program image is unverifi ed due to the program image not existing on the game disk o

15. GAME BOARDIn order to prevent electric shock and short circuit hazards, be sure to turn power off before performing work.Be careful not to damage

15-2 COMPOSITION OF THE GAME BOARDThe game board becomes the game board for this product once the key chip is inserted.The DIP SW (dip switches) on t

16. DESIGN RELATED PARTSMARQUEE HOD4 DX 62/52Part#: 515-30-100LEFT WING DECAL HOD4 62"Part#: 515-30-217PEDESTAL DECAL HOD4 DXPart#: 515-30-21962

52"DXMARQUEE HOD4 DX 62/52Part#: 515-30-100PEDESTAL DECAL HOD4 DXPart#: 515-30-219BANNER DECAL HOD4 RIGHTPart#: 515-30-220BANNER DECAL HOD4 LEFTP

17. PARTS LIST62"DXFRONTBACKSIDETOPSPEAKER LEFT SPEAKER RIGHTSTART BUTTON W/LED YELLOW (2)Part#: 99-50-005 (509-6101)GUN HOLSTER HOD

52"DXFRONTBACKSIDETOPSTART BUTTON W/LED YELLOW (2)Part#: 99-50-005 (509-6101)52"DLP PROJECTION TV LGPart#: 99-60-709GUN HOLSTE

29"STDFRONTBACKSIDETOPSTART BUTTON W/LED YELLOW (2)Part#: 99-50-005 (509-6101)29" SANWA MONITOR29E31S-BPart#: 998-0162GUN HOLS

ASSY MASK (DX CABINET) ITEM NO. PART NO. DESCRIPTION NOTE 1 HDF-0531 UPPER MASK 2 HDF-0532 LOWER MASK 3 HDF-0533 SIDE MASK 4 HDF-0

HOLSTER ASSYLIGHT FIXTURE 9" 5WATT (2)Part#: 99-60-130RUBBER PAD FOR GUN HOLSTER (2)Part#: 515-50-311GUN HOLSTER HODCOMPLETE LEFTPart#: 515-50-50

When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that the player can enjoy the game safe

CONTROL UNIT RED (515-50-310 or HDF-2100)55

ITEM NO. PART NO. DESCRIPTION NOTE 1 JPT-2030 SENSOR UNIT 2 515-30-322 (839-1280-N) XY ACCELERATION BD 3 515-50-320 (HDF

I/O CONTROL BD FOR JVSPart#: 99-10-030 (837-14505)SOUND AMP ANALOG INPart#: 99-10-033 (838-14515-A01)PWR SPLY 12 GHOST SQUAD CTFPart#: 998-0247PWR SPL

ELECTRONICS PARTS, 29”STD CABINET58LINDBERGH (MAIN CPU BD)Part#: 99-10-020 (844-0002D-14)VGA MALE TO VGA MALE CABLE 15' (52"DX)Part#: 99-60-

INSIDE OF COIN DOORSERVICE BUTTONSOUND VOLUME SWITCHTEST BUTTONCOIN METERCOIN METERSW & VOL BDPart#: 99-10-134 (838-14548)5952”/62”DX CABINET (2 s

18. WIRE COLOR CODE TABLEThe DC power wire color for this product is different from previous SEGA titles. Working from the previous wire colors will

SEGA AMUSEMENTS U.S.A., Inc.800 Arthur AvenueElk Grove Village, IL 60007-5215Phone: 888-877-2669 Fax: 847-427-10651st PRINTING, DECEMBER 2005PART#

1/2SEGA AMUSEMENTS U.S.A., INC.HOUSE OF THE DEAD 4 (29”STD, 52”/62”DX)ASSY MASK (10 SENSOR BOARDS AROUND OF MONITOR)20103012V5VC12V5VC20103020103040SH

120 VAC FAN(Cabinet)50K43K80K

*Both sideCAUTION STICKER FOR GUNHOD4 (2)Part#: 515-30-21529”STD2

2. PRECAUTIONS REGARDING INSTALLATION LOCATIONThis product is an indoor game machine. Do not install it outside. Even indoors, avoid installing in pl

3. PRECAUTIONS REGARDING PRODUCT OPERATION3-1 BEFORE OPERATIONTo avoid injury and trouble, be sure to pay attention to the behavior of visitors and p