Zenith PVR5269 Guia de Instalação descarregar pdf (Página 20)

UNIVERSAL REMOTE CONTROL

PROGRAMMING YOUR REMOTE

If you are using Zenith products, the remote is programmed for

the most commonly used codes. For otherbrands -- or if your

remote fails to control your Zenith products -- you will have

to program the remote.

Follow these steps for each product you are using:

1. Look up the three-digit code for your brand (such as

Zenith) and type of equipment (such as VCR) in the

code table on the following page.

2. Press and hold PRG with a small blunt object until

the indicator lights (about three seconds).

3. Press TV, VCR, CABLE, or AUX to select the prod-

uct you want your remote to control. (Use CABLE

or AUX, to program your remote for a second TV or

VCR or to program your remote for a video disc

player or audio equipment.)

4. Key in the three-digit code for your equipment, then

press ENTER/TUNE. The indicator light should

flash, then turn off to indicate that the code was ac-

cepted. If the indicator stays on, repeat steps 3 and 4

or try using a different code.

5. Write the codes that operate your equipment on the

label inside the battery compartment for future

reference.

To erase all code programming and return to the factory preset

codes, key in code 9-1-1 when programming the remote.

NOTES:

• The remote cannot be programmed while in the StarSight

mode: Choose TV, VCR, CABLE or AUX mode before

pressing PRG.

• If no key on your remote is pressed within 60 seconds, the

programming process will stop, and you will have to start

again.

° You may cancel programming at any time by pressing PRG.

SPECIAL FEATURES

AUX+I, AUX+2, AUX+3 Capability

Your remote can control up to seven electronic components. If

you have programmed the remote for four components using the

TV, VCR, CABLE and AUX keys, you may also program it for

up to three additional components (AUX+I, AUX+2, AUX+3)

by holding the AUX key and pressing the 1, 2 or 3 key during

programming. Once programmed, hold down the AUX key and

press 1,2 or 3, to access the additional AUX +1, 2 or 3 mode.

Cable Box Volume

You may use your remote to control cable box volume and mut-

ing if available on your equipment. Firstprogram your remote

with the bragd code for your cable device using the CABLE or

AUX key. Then repeat the progranuning steps, again using the

CABLE or AUX key, butkey in code 3-9--9 instead of a brand

code.

To restore TV volume/mute control to the CABLE or AUX

mode, reprogram your cable code into that mode.

Amplifier Volume Override

You may use your remote to override your TV, VCR or video

disk player's volume functions with your amplifier's volume and

muting.

1. Program your amplifier code into the CABLE mode

or one of the AUX modes.

2. Select the mode on your remote (TV, VCR, etc.)

where you want the amplifier volume control func-

tion to appear. In other words, if you want to oper-

ate the volume and mute of your amplifier while the

remote is in TV mode, press TV for this step.

3. Begin the programming steps as described in "Pro-

gramming Your Remote" and key in code 4-9-9, fol-

lowed by ENTER.

The amplifiervolume and mute features are now available in the

current mode.

To restore normal volume and muting control to your TV,

VCR, cable or laserdisc player, reprogram the remote for these

units into each mode (TV, VCR, etc.) to be restored.

NOTE:

• CD and tape devices will automatically select amplifier vol-

ume and mute.

2923-0t-o 4 -- 4

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 97 98

Comentários a estes Manuais

Sem comentários

Zenith PVR5269 Guia de Instalação Página 20

Comentários a estes Manuais

Manuais e produtos relacionados com TVs LCD Zenith PVR5269